Convenient Function

Touch sensor operations: You can operate the touch sensors on the earphones to change to the Bluetooth® pairing mode, or remote control the Bluetooth® device. ・Depending on the Bluetooth® device, even when you operate the touch sensors on the earphones, there may be some functions that do not work or they may act differently to the way they are described below.
■ Touch sensor operations

Function Touch operations with the touch sensors

L R

Music
Playback
Single
Single

Volume (minimum)
Double
―

Volume (maximum)
Triple
―

Forward a track
― Double

Back a track
― Triple

Call
Take call
Single
Single

Volume (minimum)
Double
―

Volume (maximum)
Triple
―

Reject call
Approximately 2 seconds
Approximately 2 seconds

End call
Approximately 2 seconds
Approximately 2 seconds

Ambient Sound Control
― Approximately 2 seconds

Start voice assistant
Approximately 2 seconds
―

Put in Bluetooth® pairing mode ●Pairing/connecting with a smartphone for the first time after purchase:
Take both earphones (L and R) out of the charging cradle
●Pairing/connecting with another smartphone:
Take out both of the earphones (L and R) from the charging cradle, and while the LEDs (blue) are illuminated (about 5 seconds), touch the touch sensor (L or R) for about 7 seconds
Refer to the operating instructions for details.

Restore factory settings Take one of the earphones out of the charging cradle, then press the touch sensor for about 7 seconds while the earphone LED (blue) is illuminated (about 5 seconds)

→After the earphone LED blinks alternately blue and red, touch the touch sensor for about 10 seconds
*Do the operation once each on both earphones (L and R).
Home screen: Connected codec
・This shows the codec being used to connect the headphones.

Codec Indicator

SBC

AAC

Note:
The codec used is selected from those codecs that your handset supports, so there may be codecs shown here that are not displayed.

Headphone name
・This shows the name of the connected headphones. ・You can edit the headphone name in "Setting" > "Headphone name".
Note button
・This is displayed only when there is a notification. ・When there is more than one notification, the number is displayed. ・You can view the notification details by tapping the Note button.
Headphone image display
・This shows an image of the connected headphones. ・You can change the color of the headphones in “Setting” > “Body color” .
Remaining headphone battery charge indicator
・This shows the charge remaining for the headphones.
Ambient Sound Control button
・You can set noise canceling and ambient sounds. ・Select the functions to set with in the screen displayed.
■Noise Cancelling Reduces the sounds (noise) you hear from outside. ・Slide to adjust the level. *You can move to a position by tapping the markers to adjust.
■Ambient Sound
You can get sounds from around you and listen to them through your headphones. ・Slide to adjust the level. *You can move to a position by tapping the markers to adjust.

Sound Enhancement button
・Sets the sound mode ・Select the items with in the screen displayed.
■CUSTOM You can set 5 sound ranges how you like.

Find headphones
・You can find headphones you have misplaced. ■When the headphones are nearby but you cannot find them (For example, when you've dropped them somewhere nearby but can't see them) → Tap "Emit sound". *Set the auto power off setting to “Always on” beforehand. ■When you have dropped them somewhere while moving and don't know where → Tap "Check position". *Tap "Switch on" beforehand. *If the app on the smartphone is operating, you can find out the location information for most recent connection.

Menu button
・Switch to each of the screens.

:Home screen
:Ambient Sound settings screen
:Sound Enhancement settings screen
:Setting screen
Settings: You can change a variety of settings for the headphones and this app in the setting screen.
(The items you can set depend on the connected model.)

Tap the setting button to display the setting screen.
Tap the item you want to set.
■Introduction

Voice prompt

Switch the language used for audio guidance on the headphones.

Headphone name

Change the “Headphone name” displayed in Home screen, etc.

The headphone name in the following screens is changed.
Headphone name screen, Home screen, Headphone list screen, etc.
Example: When the headphone name is changed to “my headphone”

Home screen Headphone list screen

Body color

The body color of the headphones shown in the Home screen changes.

■Actions

Add headphones

Pair with a new set of headphones.

Use other headphones

Connect with another set of headphones that have been paired. *This is displayed only when more than one set of headphones have been paired.

Find headphones

You can find headphones you have misplaced. ■When the headphones are nearby but you cannot find them (For example, when you've dropped them somewhere nearby but can't see them) → Tap "Emit sound". *Set the auto power off setting to “Always on” beforehand. ■When you have dropped them somewhere while moving and don't know where → Tap "Check position". *Tap "Switch on" beforehand. *If the app on the smartphone is operating, you can find out the location information for most recent connection.

■System

Auto power off

When a period of silence continues for the set time, the headphones automatically turn off.

Bluetooth blinking LED

The LEDs will blink when using the headphones.

Blinking Not blinking

The LEDs will not blink when using the headphones.

■Connection

Connection mode

Set whether to use a connection between the handset and the headphones that prioritizes sound quality or one that prioritizes connectivity.

■Operations/Sounds

Customizing the touch sensor

You can disable touch sensor operations, customize the touch sensor, etc.

■When setting whether to accept touch sensor operations

Sensor operations are disabled if you tap "OK".

■When customizing the touch sensor

For "General operations" Single tap Touch and hold

For "Telephone" Single tap when receiving a call Touch and hold when receiving a call

Double tap during a call Touch and hold during a call

-In , tap either "General operations" or "Telephone" to select which you want to customize. -In , tap or touch and hold the operation you want to change.-In , tap the function you want to change. To return the customized settings to the original settings, tap "Return to default values".

Touch Sensor Noise Cancelling Settings

Set the modes to be switched with the touch sensor operations.

Voice assistant to use

Set the voice assistant to use. *The content displayed changes depending on the voice assistant supported by the connected headphones.

■Maintenance

Website with maintenance tips

This displays the website where you can view maintenance tips.

Maintenance notification

Set whether to display "Maintenance notification" every 2 months.

Notify Do not notify

■Help

Website with help

Manual
This shows the web page with the operating instructions for the connected headphones.

How to use the app
This displays a website where you can view information about how to use this app.

Troubleshooting
This displays the website where you can view tips to solve problems.

Note
You can view notification details.

Firmware update information
This displays the website for firmware updates.

To get the right fit
You can view how to properly fit the earphones.

Headphone information

You can view product information about the headphones.

・You can view the current version of the firmware used in the headphones in “Firmware version”. If the latest version of the firmware is detected, tap “Update available”.

About the application

You can view information about this app.

・You can display license information if you tap "User license information". ・You can display the privacy policy from the viewpoint of the protection of personal data if you tap "Privacy Policy". ・In "Share error data", set whether to upload to the log server the logs acquired by this app from the headphones and the logs kept by this app. ・You can return to the condition immediately after installing this app if you tap "Initialize app". *Bluetooth pairing information is maintained.
Checking the firmware version and updating: You can use this app to update the firmware of the connected headphones.

・When there are multiple notifications, tap the Note button in the Home screen to display the notifications list screen, then tap "A headphones update is available."
When you tap "Update now", the firmware is transferred to the headphones and the update is made. Transfers may be interrupted or slowed down if music is played back or there is a call during the transfer. Start the transfer with the headphones outside of the charging cradle, set down close by and do not operate them.

Wait until the update completes, without operating the headphones or the app. ・After updating the firmware, the headphones automatically restart and reconnect with the handset.
Until the update completes, the app will not work properly even if you try to operate it, so do not try to operate the headphones or the app.

If “Firmware is up to date.” is displayed in “Setting” > "Headphone information”, the firmware has been update to the latest version.
Updating the firmware is also available with "Setting" > "Website with help" > "Note".

Function	Touch operations with the touch sensors
L	R
Music	Playback	Single	Single
Volume (minimum)	Double	―
Volume (maximum)	Triple	―
Forward a track	―	Double
Back a track	―	Triple
Call	Take call	Single	Single
Volume (minimum)	Double	―
Volume (maximum)	Triple	―
Reject call	Approximately 2 seconds	Approximately 2 seconds
End call	Approximately 2 seconds	Approximately 2 seconds
Ambient Sound Control	―	Approximately 2 seconds
Start voice assistant	Approximately 2 seconds	―
Put in Bluetooth® pairing mode	●Pairing/connecting with a smartphone for the first time after purchase: Take both earphones (L and R) out of the charging cradle ●Pairing/connecting with another smartphone: Take out both of the earphones (L and R) from the charging cradle, and while the LEDs (blue) are illuminated (about 5 seconds), touch the touch sensor (L or R) for about 7 seconds Refer to the operating instructions for details.
Restore factory settings	Take one of the earphones out of the charging cradle, then press the touch sensor for about 7 seconds while the earphone LED (blue) is illuminated (about 5 seconds) →After the earphone LED blinks alternately blue and red, touch the touch sensor for about 10 seconds *Do the operation once each on both earphones (L and R).