Device LED indicators
Each device can provide information about its status by turning on its LED indicator.
Meaning of symbols used in this section
 | Indicator off |
 | Indicator lit |
 | Indicator blinking slowly |
 | Indicator blinking |
 | Indicator blinking quickly |
 | Indicator blinking very quickly |
 | Indicator blinking slowly in two colors |
 | Indicator blinking in two colors |
Access point LED indicator
Off | | No power, or LED indicator is turned off *1 |
Green |  | Power is on (normal operations)*1, or registration completed for the camera or mobile device |
 | Registration mode, updating | |
 | Obtaining an IP address, or accessing a microSD card*1 | |
Green or yellow (amber) (alternating) | or  | Starting up*2 |
Red |  | Registration failed |
Yellow (amber) | | Power on until start up completed |
 | IP address is not obtained, or Ethernet cable is not connected to the router |
*1
You can configure the access point so that its LED indicator does not light in most states. See Status LED.
*2
It may take some time for the access point to finish starting up.
Front door camera and outdoor camera LED indicator
Off | | • No power • More than 5 seconds have passed since turning on the power when the camera is not registered to the access point • LED indicator is turned off*1 |
Green | | Registration successfully completed or signal level is strong*3 |
| Registration mode, updating | |
| Camera is searching for an access point*1 | |
Green or yellow (amber) blinking quickly - off for 1 second | or | Camera is on*1 |
Red | | |
 | ||
 | Streaming data*1 | |
Yellow (amber) | | |
 | Battery is running low*1 |
*1
You can configure the camera so that its LED indicator does not light in most states. See Status LED.
*2
The LED indicator lights in yellow (amber) for 5 seconds after the power is turned on for the camera.
*3
The signal level (strong, good, weak, out of range) is shown after pressing the SETUP button for 3 seconds. You can also check the signal level from Camera signal strength.
*4
Motion detection can also be checked from Detection test.
Front door camera and outdoor camera charging LED indicator
Red | | Charging is completed |
| Charging | |
| Charging failure |
HD camera LED indicator
Off | | No power, or LED indicator is turned off*1 |
Blue |  | Normal operation, connected to wireless router*1, privacy shutter is open |
White |  | Normal operation, connected to wireless router*1, privacy shutter is closed |
 | Camera is searching for wireless router | |
Green | | Initial setup required |
| Initial setup is in progress with mobile device connected | |
 | Initial setup is starting | |
Red | | Motion detected*1, or camera is starting up |
| Live images are being viewed or recorded, or camera is starting up | |
 | Device malfunction |
*1
You can configure the camera so that its LED indicator does not light during normal operation or when motion is detected. See HD camera device profiles.
Floor camera LED indicator
Off | | • No power • LED indicator is turned off*1 |
Green | | |
| Registration mode, updating | |
| Camera is searching for your wireless router | |
Blinking every 1.5 seconds | | Batteries for power backup are in use |
Red | | |
| ||
| • Camera is out of range of your wireless router*2 • LED lights are abnormally hot • Wireless LAN connection failed | |
Yellow | | Not registered to your wireless router (usually for initial setup), or signal level is good*2 |
| Initial setup is being performed using WPS on your router | |
Blue | | Registration to your wireless router successfully completed or camera is on*1 |
White | | Privacy mode is on*1 |
 | Accessing microSD card (when privacy mode is on) |
*1
You can configure the camera so that its LED indicator does not light in most states. See Status.
*2
The signal level (strong, good, weak, out of range) is shown after pressing the SETUP button for 3 seconds. You can also check the signal level from Camera signal strength.
*3
Lights for 3 seconds after registration is successfully completed or failed.
Shelf camera LED indicator
Off | | • No power • LED indicator is turned off*1 |
Green | | |
| Registration mode, updating | |
| Camera is searching for your wireless router | |
Red | | |
| ||
| • Camera is out of range of your wireless router*2 • Wireless LAN connection failed | |
Yellow | | Not registered to your wireless router (usually for initial setup), or signal level is good*2 |
| Initial setup is being performed using WPS on your router | |
Blue | | Registration to your wireless router successfully completed or camera is on*1 |
White | | Privacy mode is on*1 |
| Accessing microSD card (when privacy mode is on) |
*1
You can configure the camera so that its LED indicator does not light in most states. See Status.
*2
The signal level (strong, good, weak, out of range) is shown after pressing the SETUP button for 3 seconds. You can also check the signal level from Camera signal strength.
*3
Lights for 3 seconds after registration is successfully completed or failed.
Window camera LED indicator
Off | | • No power • LED indicator is turned off*1 |
Green | | |
| Registration mode, updating | |
| Camera is searching for your wireless router | |
Red | | |
| ||
| • Camera is out of range of your wireless router*2 • Wireless LAN connection failed | |
Yellow | | Not registered to your wireless router (usually for initial setup), or signal level is good*2 |
| Initial setup is being performed using WPS on your router | |
Blue | | Registration to your wireless router successfully completed or camera is on*1 |
*1
You can configure the camera so that its LED indicator does not light in most states. See Status.
*2
The signal level (strong, good, weak, out of range) is shown after pressing the SETUP button for 3 seconds. You can also check the signal level from Camera signal strength.
*3
Lights for 3 seconds after registration is successfully completed or failed.