SC-ALL70T / SC-ALL30T FAQs

• Connect this unit to the network.
     - Make sure that the network is connected to the Internet.
• Check that [ ] is indicated on the display.
     - When this unit connect to the network, [ ] is indicated on the unit's display.
     - If it is not indicated, check the network settings.

1. Press [SETUP] repeatedly to select "F/W UPDATE" and then press [OK].
2. Press [] [] to select "UPDATE YES" and then press [OK] to start the update.
   • "WAIT" blinks on the display.
     DO NOT DISCONNECT the AC mains lead while one of the following messages is displayed.
     "UPDATING" or " %" (" " stands for a number.)
     • During the update process, no other operations can be performed.
   • After the update has finished, "SUCCESS" is displayed, and then "PLEASE DISCONNECT AC MAINS LEAD" scrolls.
3. Disconnect the AC mains lead and reconnect it after 3 minutes.

• Downloading will require about 15 minutes. It may take longer or may not work properly depending on the connection environment.
• You cannot output sound from this unit while updating the firmware.
• To view the TV during update, change the settings on the TV to have the sound output from the TV's speakers. Refer to the operating instructions of the TV for details.

* If there are no updates, "NO NEED" is displayed.

* Refer to firmware update troubleshooting as bellow.

• This unit is not connected to the network. Check the network settings.
• The update has been failed. Touch any switch, and then try again.
• When using a LAN cable,make sure to connect the LAN cable while the AC power supply cord (AC main lead) is disconnected.
• An error has occurred. Disconnect the AC power supply cord (AC mains lead) and reconnect it. Turn the unit on and try again.

1. Turn this unit on.
   • If the network indicator is blinking in blue and red, proceed to the next step after the blinking stops.
2. Touch and hold [ ].
   • The operation indicator (amber) starts to blink.
3. While continuing to hold [ ], touch and release [NET].
   • The operation indicator (amber) blinks 4 times.

• Because some Internet browser cannot inform its language information correctly, the pages may be displayed in the other language (default, e.g. English). At this moment (Oct. 2016) Chrome and Opera browser can display with the language of your mobile device.
• If you set the Chrome and Opera browser as default browser in your mobile, you can see the pages in your language.

• Check the distance between this unit and your wireless LAN router. Please locate it closer with each other.
• Make sure that the multicast function on your router is enabled.
• For details, refer to the operating instructions of your router.
• To using WPS, turn off and then on the unit, and redo the network settings
  (Refer "Network Setting" of "Operating Instructions")
• Depending on the routers, WPS button may not work. Try other methods which is shown in "Network Setting" of "Operating Instructions".
• If still cannot connect, please use the setting method for "Using an internet browser" or "Using a LAN cable" which is shown in "Network Setting" of "Operating Instructions".

"Operating Instructions" can be downloaded at the followings links.

• This unit's Wi-Fi security supports WPA2™ only. Your wireless LAN router must therefore be WPA2™ compatible. For details on the security supported by your router and how to change the settings, please refer to the operating instructions or contact your Internet service provider.
• Depend on the router's model and setting, even though it is successfully connected, the connection may become disconnected. Try to change router setting to use WPA2™ only.
• If the network is set to be invisible make the network visible while you set up the network for this unit or make a wired LAN connection.
• For details, refer to the operating instructions of your router.

http://www.panasonic.com/global/consumer/homeav/allseries/service/

• Please select the AllPlay Speaker once, and try again.
• If using the 2.4 GHz band on your wireless LAN router, simultaneous use with other 2.4 GHz devices, such as microwaves, cordless telephones, etc., may result in connection interruptions. Increase the distance between this unit and these devices.
  - If your wireless LAN router supports 5 GHz band, try using the 5 GHz band.
     To change to the 5 GHz band, perform a network reset, and redo
     the network settings using an Internet browser.
     Operating Instructions (English only)
     Select your network name (SSID) for the 5 GHz band.
• Do not place this unit inside a metal cabinet, for it might block the Wi-Fi signal.
• Place this unit closer to your wireless LAN router.
• If several wireless devices are simultaneously using the same network as this unit, try turning off the other devices or reducing their network usage.
• Reconnect the devices to the network.
• Turn off and then on your wireless LAN router.
• Try a wired LAN connection.
• If The sound would be interrupted while you are enjoying Internet radio, it may be improved when you select the station in "AllPlay Radio" Application and change the stream (e.g. 128kbps MP3) in "Choose stream" option menu.
  (Depends on the station you selected, you may not able to change/ or choose the stream.)