Global Home Digital AV Support > Audio > Download > SC-AKX300 / AKX500 / AKX700 / AKX900 Software Update service

SC-AKX300 / AKX500 / AKX700 / AKX900 Software Update service

Step 4. Decompress the downloaded file

Check the file size of the downloaded file and decompress it. (Supported for Windows only.)

  1. Checking the file size
    Right click on the downloaded software, and select "Properties". Make sure that the size of the file is the same as the size listed on the download page.
    If the file size differs, please download it again. After checking the size, click [OK] and the "Properties" window will close.
  2. Decompressing the file
    Double click the downloaded software and decompress it.
    The decompressed file will be named as "AKX300.FRM" for SC-AKX300 or "AKX500.FRM" for SC-AKX500 or “AKX700.FRM” for SC-AKX700 or “AKX900.FRM” for SC-AKX900.
Step 5. Preparing the USB device

Before start creating the update USB device, please check update file to make sure it has correct file name.
It is important to use the correct file, otherwise USB version up process will not work.
Below are the file name and file for your reference:

Model
Region
File name
AKX300
All Region
AKX300.FRM
AKX500
All Region
AKX500.FRM
AKX700
All Region
AKX700.FRM
AKX900
All Region
AKX900.FRM
  • Please prepare USB device which memory is less than 32GB and file format FAT or FAT32.(not support exFAT)
  • To create USB update, copy the FRM file (depends on model) into USB root folder.

Note:
Do not rename the file as the updating process will look for above naming. If different name, version up process will not work.

Step 6. Software Update
Caution:
  • During the updating process, do not disconnect the AC power supply cord.
  • Do not press any buttons, except as instructed. Failure to do so may result in the set becoming unresponsive which will require repair.
    Steps:
  1. Press [USB/CD] (AKX300) / [ USB] (AKX500 / AKX700 / AKX900) repeatedly to select "USB B". Insert USB device (With "AKX300.FRM" or "AKX500.FRM" or “AKX700.FRM” or “AKX900.FRM” file inside).
  2. When "UPDATE" is displayed, press OK. Display will change to "OK? NO".
  3. Press [ ](AKX300) /[ ] (AKX500 / AKX700 / AKX900) button to change to "OK? YES".
  4. Press [OK] button.
  5. During update process, the display will gradually change from "UPD 0%" up to "UPD 100%".
  6. When "SUCCESS" display appears, unplug USB then unplug AC cable. Software updating process is now complete.

    NO NEED: the software is already latest version and no need to update.
  7. Follow 'Step 1: Check the software version currently installed in your SC-AKX300 / AKX500 / AKX700 / AKX900' to confirm the updated software version. It should be according to the 'Update version' from the above 'Update Information' table.
Note:
  • After updating process successfully finished, delete the update file ("AKX300.FRM" or "AKX500.FRM" or “AKX700.FRM” or “AKX900.FRM”) from the USB device. Otherwise, updating process will start again if insert this USB device to this unit.
  • If you found that the model is working abnormally after updating the software, confirm that you have downloaded the correct updating file according to your model's region or not. If it is not correct, re-select the correct region for your model and redo the downloading and updating process again.
  • In the event the software update process is interrupted, please follow these steps. Unplug the AC power supply and remove the USB device from the USB B port
  1. Plug in the AC power supply.
  2. When the set displays "INSERT USB B", plug in the USB device back to USB B port

    The display will then show "UPDATING", then it will proceed with the recovery process. The display will gradually change from "UPD 0%" up to "UPD 100%".

    Note:
    In case the set display does not change to "UPDATING", plug out and plug in the USB device to USB B port. Repeat this until the USB device is properly detected.
  3. When "SUCCESS" display appears, unplug USB then AC out supply. Software recovery process is now complete.